Відео

❤

They are not doing that digging,😂. Some one else is off camera.

What else did you and Jen do in the attic?

❤

Great tutorial. Figured I needed an extractor bit, so I ran to Home Depot to get a set. Came back, followed your instructions precisely, and didn't even need to flip the bit as the screw began coming out already. Slow and steady was key. Thank you! You saved me a lot of headache and probably a lot of money, too

Hi! Thank you for very useful video and great tips. I tried to do something similar, but something went a bit off, so I’m kindly asking you for an advice: I have a wooden IKEA table. Its top made of several wooden blocks, so it’s not a single sheet of wood. I dyed it using water-based dye, and covered it with the first coat of polyurethane lacquer. The thing is that after applying the first coat I can see that the surface gone patchy - some wooden blocks are glossy and smooth, and some - dull and a bit rough to the touch, where the wood absorbed the lacquer. I was going to use fine sandpaper to even the surface after the first coat of lacquer. But now I’m a bit confused as I don’t know if I could damage the dye layer on the dull patches and expose the wood, as it is obviously very thin. What would you suggest to do in this case? I was going to do at least three coats of lacquer with sanding in between.

Not if Biden closes Texas immigrants detention center and other blue states do something similar …

Nicely done! Good discussion of the process and choices. Thanks!

Very helpful! Thank you!

Great info, well presented. Thanks.

Is there some type of grout topping that repels the dirt from re-saturating new white grout?

1:08

No thankyou.

Before you give up on the screwdriver, try topping while twisting. The shock off the hammer blows reduces the pressure on the threads.

Great 👍🏽

Well done detective

I need this but for electronics screws like the ones in phones

Great video Thank you

Looks pretty handy

Now you lost 1/4” of height storage

this reminds me of the all in the family episode where archies house needs aluminum siding.

Good job Ron I been watching your work for years thank you ,thank you I’ve learned a lot from you

I need the fifth method.

Congratulations on season 18. Great video.

Love the show Ron

Groovy

1:04 Hi Ron My husband and I are going to make a dinning room table and I’m not sure what kind of wood to use we live in Florida what would be the best durable wood to use. Thank you

Good video. Others talk for 2 hours on 25 second job.

Woah Father Fish is very talented

I know the video is old, but where did the sheets come from? Is the process the same for plastic/ styrofoam ceilings? Thx!

What would work best for a table leg mounted by 4 screws to the underside of a 1/2" to 3/4" desktop (possibly made out of particle board with a finished top)? The length of leg can put a lot of leverage on 4 closely spaced screws that are about 2" apart.

Anyone else notice the video was reversed? The step drill bit was going “backwards” against the rotation of normal drills 🧐

This was a great video, i'm gonna try this for my home desk drawers and then if it works properly I"ll do it for my desk drawers at work. :D

My stupid daughter punched several holes in my door! It would cost $1,100 to replace the door because it needs to be custom made. Thanks for the video. I'm doing this instead!

What is the best coat for Butcher Block counter by the kitchen sink and what would be the best way to seal under the sink to prevent leaks and rot THANK YOU !!!!!

Excellent video ! Thank you !

I had forgotten to swap out the drill bit when installing a child gate and made the hole a tad too big. The toothpick trick worked perfectly.

Thank you, Mister! All that was really helpful! 👍🏼👍🏼

Why doesn’t anybody talk about the lead in old paint? If you are vacuuming up lead paint with anything other than a Hepa rated vacuum then you are creating a lead hazard in your shop as the vacuum’s exhaust will redistribute the lead dust in the old paint you are removing .

I really enjoyed this video and the editing too! Thanks

ooh, that last option is clever, love it. A hacksaw to convert any screw head type into standard. Thanks!

Good video great information. However you should explain that there are two different types of drill bits for concrete. A bit for use in a hammer drill is useless in a plain rotary drill motor.

I really appreciate your videos mate. Your narration is educational yet succinct. And like others, the lack of annoying music or any other needless production is really appreciated. Thank you